{"id":951,"date":"2026-06-18T07:35:55","date_gmt":"2026-06-18T07:35:55","guid":{"rendered":"https:\/\/planetary-gearboxes.com\/?post_type=product&p=951"},"modified":"2026-06-18T07:35:55","modified_gmt":"2026-06-18T07:35:55","slug":"410w3-winch-drive-planetary-gearbox","status":"publish","type":"product","link":"https:\/\/planetary-gearboxes.com\/bs\/proizvod\/410w3-winch-drive-planetary-gearbox\/","title":{"rendered":"410W3 Winch Drive Planetary Gearbox Reducer"},"content":{"rendered":"
\n

<\/p>\n

\n
\n
410 FAMILY \u00b7 DUAL-MOTOR TERRITORY<\/div>\n

37,500 Nm<\/h2>\n

Where two motors meet one drum.<\/p>\n

\n
\n
62-177<\/div>\n
Omjeri<\/div>\n<\/div>\n
\n
530<\/div>\n
Nm Brake<\/div>\n<\/div>\n
\n
390<\/div>\n
kg<\/div>\n<\/div>\n
\n
M5<\/div>\n
FEM Duty<\/div>\n<\/div>\n<\/div>\n<\/div>\n

The EP-410W3 is the first model in the winch drive planetary gearbox<\/a> catalogue where the data sheet lists a dual-motor input configuration as the primary architecture rather than a single-motor option. At 37,500 Nm through ratio 100, the motor input torque is 375 Nm \u2014 requiring approximately 675 cc\/rev from a single motor at 350 bar, which exceeds the practical limit of most axial piston motor catalogues. Two motors at 338 cc\/rev each, sharing the input through a Y-adapter, bring the individual motor size back into standard catalogue territory while doubling the available input power for faster hoisting speeds.<\/p>\n

\"410W3<\/p>\n

The ratio range extends to 177 \u2014 the highest maximum in the 4xxW series to this point \u2014 serving applications where the drum must turn extremely slowly. At ratio 177 with a 2,000 rpm motor, the drum output is 11.3 rpm. On a 600 mm PCD drum, this produces a line speed of 21.3 m\/min \u2014 a controlled crawl for deploying heavy subsea equipment through the splash zone or lowering a mine cage through a 500-metre shaft.<\/p>\n<\/section>\n

\n

410W3 Winch Drive Planetary Gearbox \u2014 Technical Parameters<\/h2>\n
\n\n\n\n\n\n\n\n\n\n\n\n\n\n
Nazivni izlazni obrtni moment<\/td>\n37,500 Nm<\/td>\n<\/tr>\n
Gear ratio range<\/td>\n62 to 177 (three-stage planetary)<\/td>\n<\/tr>\n
Maximum input speed<\/td>\n3,500 rpm<\/td>\n<\/tr>\n
Maximum output speed<\/td>\n25 rpm (FEM M5 continuous duty)<\/td>\n<\/tr>\n
Mechanical efficiency<\/td>\n\u2265 95%<\/td>\n<\/tr>\n
Parking brake<\/td>\n530 Nm, multi-disc, spring-applied, hydraulic release<\/td>\n<\/tr>\n
Brake at drum (ratio-dependent)<\/td>\n32,860 Nm (r=62) to 93,810 Nm (r=177)<\/td>\n<\/tr>\n
Mounting<\/td>\nRotating housing flanges<\/td>\n<\/tr>\n
Dry weight<\/td>\nApprox. 390 kg<\/td>\n<\/tr>\n
Podmazivanje<\/td>\nOil bath splash, EP gear oil<\/td>\n<\/tr>\n
Radna temperatura<\/td>\n-20 to +85 deg C<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n<\/section>\n

<\/p>\n

\n

Dual-Motor Winch Architecture \u2014 How Two Motors Drive One Drum Through the 410W3<\/h2>\n

At 37,500 Nm, the single motor input torque exceeds standard motor frames at most ratios. The solution is not a bigger motor \u2014 it is two standard motors sharing the mechanical input through a Y-adapter gearbox or a dual-spline input shaft.<\/p>\n

\n
\n

Y-Adapter Configuration<\/strong><\/p>\n

A Y-adapter gearbox mounts between two motors and the 410W3 input shaft, combining the torque from both motors onto a single output spline. Each motor contributes half the required input torque. At ratio 100: each motor provides 188 Nm instead of 375 Nm, requiring approximately 338 cc\/rev each at 350 bar \u2014 comfortably within standard variable-displacement motor frames (Rexroth A6VM355, Parker V14-160, Eaton 420 series). The Y-adapter adds approximately 15-25 kg and 100-150 mm of axial length to the motor-gearbox assembly.<\/p>\n<\/div>\n

\n

Torque Synchronisation<\/strong><\/p>\n

Both motors are fed from the same hydraulic supply line, so they operate at identical pressure. If the motor displacements are matched (both set to the same cc\/rev), both produce equal torque and share the load evenly. If one motor is set to a slightly different displacement (for example, during controlled lowering where one motor acts as a brake), the torque split becomes asymmetric \u2014 the 410W3 input shaft and the Y-adapter must be rated for the full torque in case one motor carries the entire load momentarily during transients.<\/p>\n<\/div>\n

\n

Redundancy Benefit<\/strong><\/p>\n

If one motor fails (seized shaft, internal leakage, hose burst), the remaining motor can still drive the 410W3 at half torque and half speed \u2014 enough to complete a critical lift or lower a suspended load safely rather than relying solely on the parking brake. This inherent redundancy is a significant safety advantage for offshore and mining applications where a winch failure with a suspended load creates an emergency. Some classification societies recognise dual-motor configurations as a form of hoist drive redundancy, simplifying the approval of cranes for over-water personnel transfer.<\/p>\n<\/div>\n

\n

Speed Range Expansion<\/strong><\/p>\n

Two variable-displacement motors provide twice the flow capacity of a single motor at the same system pressure. At low speed (both motors at maximum displacement), the winch delivers maximum torque. At high speed (both motors de-stroked to minimum displacement), the winch hoists light loads at double the line speed achievable with a single motor. This variable-speed range \u2014 from creep to fast \u2014 is managed entirely by the motor controller without any mechanical speed change in the gearbox. Contact Korea Ever-Power<\/a> for dual-motor integration drawings and the recommended Y-adapter specifications.<\/p>\n<\/div>\n<\/div>\n<\/section>\n

<\/p>\n

\n

Ratio 177 \u2014 Where 500-Metre Shaft Depths Dictate the Drum Speed<\/h2>\n

The 410W3 ratio range extends to 177 \u2014 30% higher than the 407W3 maximum of 136. This additional reduction serves a specific class of applications where the cable length is hundreds of metres and the winch must maintain precise speed control over the entire descent.<\/p>\n

\n
\n

Deep Mining Shaft Winders<\/h3>\n

Mine shaft service winders lowering cages, skips, and equipment to working levels at 300-700 metres depth. At ratio 177 on a 700 mm PCD drum with dual motors at 2,500 rpm: drum output = 14.1 rpm, line speed = 31 m\/min. A 500-metre descent takes approximately 16 minutes at this speed. The high ratio ensures the motors operate at efficient mid-range speed (2,000-3,000 rpm) throughout the descent rather than crawling at low speed where motor efficiency and controllability degrade. The 530 Nm brake holds 93,810 Nm at the drum \u2014 sufficient for the combined weight of the cage, payload, and 500 metres of wire rope.<\/p>\n<\/div>\n

\n

Subsea Construction Vessel A&R Winches<\/h3>\n

Abandonment and recovery (A&R) winches on pipe-lay and subsea construction vessels handling umbilicals, risers, and flowlines at water depths of 200-500 metres. The combined weight of the product and the cable at these depths produces drum torques approaching the 410W3 capacity. At ratio 150-177, the controlled deployment speed (5-15 m\/min) protects the product from shock loading at the seabed touchdown \u2014 while the slewing drive<\/a> positions the overboard chute and the track drive<\/a> handles the vessel anchor winch crawlers.<\/p>\n<\/div>\n<\/div>\n<\/section>\n

<\/p>\n

\n

37,500 Nm \u2014 The Dual-Motor Winch Drive for Extreme Lifting and Deep Deployment<\/h2>\n

\"410W3<\/p>\n

\n
\n

Large Floating and Sheerleg Cranes (30-60 t SWL)<\/h3>\n

Floating cranes, sheerleg cranes, and heavy-lift barges positioning bridge sections, lock gates, and offshore platform topsides. The 410W3 at ratio 80-120 with dual motors provides the torque for 30-60 tonne lifts and the redundancy that marine classification societies require for over-water heavy lifting. The dual-motor architecture means the crane can complete a lift with one motor failed \u2014 a capability that single-motor systems at the 407W3 level cannot provide.<\/p>\n<\/div>\n

\n

Offshore Construction Vessel Cranes<\/h3>\n

Main hoist mechanisms on dedicated offshore construction vessels (DSVs, pipe-lay vessels, heavy-lift vessels) handling subsea trees, manifolds, and umbilical termination assemblies at water depths requiring 200-500 metres of wire rope on the drum. The combined rope weight and payload weight at these depths pushes the drum torque into the 30,000-37,500 Nm range. The 410W3 provides the torque, the 530 Nm brake provides the holding capacity, and the ratio 150-177 provides the controlled deployment speed through the critical splash zone<\/a>.<\/p>\n<\/div>\n

\n

Deep Mining Shaft Winders and Skip Hoists<\/h3>\n

Mine shaft winders handling personnel cages (500-1,500 kg payload), skip hoists (5-15 tonne ore skips), and equipment lowering at shaft depths of 300-700 metres. Mine safety authorities in most jurisdictions require the winder brake to hold the cage plus the full cable weight at the deepest point \u2014 a combined load that can exceed 30 tonnes when 500+ metres of heavy-gauge rope is factored in. The 410W3 at ratio 150-177 provides both the controlled hoisting speed and the brake holding torque that deep-shaft winding demands.<\/p>\n<\/div>\n<\/div>\n<\/section>\n

<\/p>\n

\n

The Ultra-Heavy Winch Drive Tier<\/h2>\n
\n
\n

\"Winch<\/p>\n

\n

Full Winch Drive Range \u2192<\/a><\/h3>\n

413W3 (42,500 Nm) to 419W3 (330,000 Nm) for the largest lifting and winding operations in the world.<\/p>\n<\/div>\n<\/div>\n

\n

\"Slewing<\/p>\n

\n

Slewing Drive Planetary Gearbox \u2192<\/a><\/h3>\n

ZR series for large floating crane rotation, offshore vessel crane slewing, and headframe sheave positioning.<\/p>\n<\/div>\n<\/div>\n

\n

\"Wheel<\/p>\n

\n

Wheel Drive Planetary Gearbox \u2192<\/a><\/h3>\n

EP 6xx\/ZL24 series for heavy crane carrier travel and mining vehicle propulsion.<\/p>\n<\/div>\n<\/div>\n<\/div>\n<\/section>\n

<\/p>\n

\n

Winch Drive Planetary Gearbox \u2014 Dual-Motor Heavy Hoist FAQ<\/h2>\n
\n
\n

Can the 410W3 operate with a single motor for light-load hoisting?<\/h3>\n

Yes. One motor can drive the 410W3 at up to half the rated torque (approximately 18,750 Nm) and half the maximum hoisting speed. The idle motor free-wheels through the Y-adapter if equipped with a check valve that prevents back-flow. For cranes that handle both heavy and light loads, the control system can engage both motors for heavy lifts and de-stroke one motor to idle for light loads \u2014 saving hydraulic power and reducing pump wear during the majority of cycles that do not approach maximum capacity.<\/p>\n<\/div>\n

\n

How does cable weight affect the brake holding calculation for deep shaft applications?<\/h3>\n

Significantly. A 500-metre length of 28 mm diameter wire rope weighs approximately 2,000 kg (4.0 kg\/m). The brake must hold the payload PLUS the cable weight: for a 10-tonne skip at 500 metres on a 600 mm PCD drum: T(load) = (10,000 + 2,000) x 9.81 x 0.3 = 35,316 Nm. The 530 Nm brake at ratio 177 produces 93,810 Nm \u2014 giving SF = 2.66. Without the cable weight: T(load) = 10,000 x 9.81 x 0.3 = 29,430 Nm, SF = 3.19. The cable weight reduces the safety factor by 17% \u2014 a substantial and frequently underestimated effect that must be included in every deep-shaft brake calculation.<\/p>\n<\/div>\n

\n

What happens if one motor in the dual-motor configuration fails during a heavy lift?<\/h3>\n

The remaining motor assumes the full load \u2014 which may exceed its individual torque capacity. The Y-adapter check valves prevent the failed motor from back-driving. The crane control system should detect the motor failure (via pressure or flow sensors) and immediately reduce the hoist speed to prevent the remaining motor from overheating. The 530 Nm parking brake can be engaged to hold the load stationary while the situation is assessed. In most cases, the remaining motor can complete the lift at reduced speed (50% of normal) or lower the load safely to the ground or deck. This degraded-mode capability is a key advantage of dual-motor architecture for safety-critical lifts.<\/p>\n<\/div>\n

\n

What oil volume does the 410W3 require?<\/h3>\n

Approximately 8-12 litres depending on mounting angle and the specific ratio (three-stage high-ratio variants have slightly more internal volume). Use API GL-5 SAE 80W-90 or ISO VG 150 EP gear oil. First change at 250 hours. Subsequent changes every 1,500 hours for offshore and mining applications. Oil sampling every 500 hours is mandatory at this torque class \u2014 the cost of an undetected bearing failure on a crane handling 30+ tonne loads or a deep mine cage is measured in days of lost production and potential safety incidents. Contact Korea Ever-Power<\/a> for the specific oil charge volume for your serial number and ratio.<\/p>\n<\/div>\n

\n

Can the 410W3 winch drive handle the dynamic loads from vessel motion during offshore lifts?<\/h3>\n

Yes, within the dynamic amplification limits. Wave-induced vessel motion creates oscillating cable tensions that can reach 1.5-2.5 times the static load in significant wave heights of 2-4 metres. The 410W3 at 37,500 Nm continuous with a 2x peak capacity (75,000 Nm transient) can absorb dynamic amplification factors up to 2.0 at rated load. For lifts in sea states exceeding 3 metres significant wave height, an active heave compensation (AHC) system between the motor and the gearbox reduces the dynamic amplification factor to approximately 1.1-1.3 by adjusting motor speed in real time to match the vessel heave. The gearbox transmits whatever the AHC system commands.<\/p>\n<\/div>\n

\n

How does the winch drive planetary gearbox integrate with an active heave compensation system?<\/h3>\n

The AHC system is implemented entirely in the hydraulic circuit \u2014 it adjusts the motor speed and direction in real time to keep the load stationary relative to the seabed while the vessel heaves. The 410W3 gearbox is a passive component in this system: it transmits whatever torque and speed the AHC controller commands through the motors. No gearbox modification is needed for AHC integration. The only gearbox-related AHC consideration is input speed: AHC systems can command rapid speed reversals (from hoisting to lowering in under 1 second), and the 410W3 input shaft must sustain these reversals at up to 3,500 rpm. The planetary gear train handles torque reversal identically in both directions.<\/p>\n<\/div>\n<\/div>\n<\/section>\n

<\/p>\n

\n

Field Reports<\/h2>\n
\n
\n
\n
H<\/div>\n
\n
Henk V. \u2014 Floating Crane Fleet Manager<\/div>\n
Verified Purchase \u00b7 Rotterdam, Netherlands \u00b7 April 2026<\/div>\n<\/div>\n
\u2605\u2605\u2605\u2605\u2605<\/div>\n<\/div>\n

50 t sheerleg crane, main hoist, 410W3 at ratio 100, dual 350 cc\/rev motors. The crane positioned a 48-tonne steel bridge section to within 8 mm during the most recent installation. During the lift, one motor developed a minor case drain leak \u2014 the control system detected the flow anomaly, alerted the operator, and the lift was completed on both motors before the leak became critical. After the section was in place, we isolated the leaking motor and lowered the hook on the remaining motor at half speed. This is exactly the redundancy we specified the dual-motor system to provide \u2014 and it delivered. The motor was replaced the following day; the gearbox required no attention.<\/p>\n<\/div>\n

\n
\n
T<\/div>\n
\n
Thiago R. \u2014 Subsea Construction Vessel Engineer<\/div>\n
Verified Purchase<\/div>\n<\/div>\n
\u2605\u2605\u2605\u2605\u2605<\/div>\n<\/div>\n

A&R winch on a subsea construction vessel, 410W3 at ratio 165, deploying a 15-tonne subsea manifold to 350 metres water depth. Total cable weight at maximum depth: approximately 1,800 kg. The controlled descent at 8 m\/min through the splash zone was smooth \u2014 the AHC system compensated for 2.5-metre vessel heave and the 410W3 transmitted the rapid speed reversals without any audible stress or vibration anomaly. The brake held the manifold at 350 metres for 45 minutes during the ROV survey before final landing. After 14 months including 8 major subsea deployment campaigns, the gearbox oil analysis is clean and the brake test is within 2% of factory acceptance values.<\/p>\n<\/div>\n

\n
\n
V<\/div>\n
\n
Victor N. \u2014 Mining Shaft Engineer<\/div>\n
Verified Purchase \u00b7 June 2026<\/div>\n<\/div>\n
\u2605\u2605\u2605\u2605\u2606<\/div>\n<\/div>\n

Personnel cage winder for a 480-metre deep platinum mine shaft, 410W3 at ratio 170, dual motors. The cage carries 12 workers plus the cage weight totalling 2,800 kg. With 480 metres of 32 mm rope at 5.2 kg\/m: cable weight = 2,496 kg. Total suspended load at full depth = 5,296 kg. Brake SF at drum = 93,810 \/ (5,296 x 9.81 x 0.3) = 6.0 \u2014 well above the mine safety authority minimum of 3.0 for personnel winding. The 4-star is a commissioning observation: the Y-adapter alignment between the two motors required shimming on site because the adapter mounting face was not perfectly parallel to the motor flanges. Pre-aligning the Y-adapter to the 410W3 input at the factory before shipping would have saved 2 days of commissioning time. The winder itself has been faultless through 9 months of 3-shift daily operation.<\/p>\n<\/div>\n<\/div>\n<\/section>\n<\/div>","protected":false},"excerpt":{"rendered":"

The EP-410W3 enters the territory where single-motor hydraulic architecture is no longer sufficient and dual-motor configurations become the standard engineering practice. At 37,500 Nm through three planetary stages with ratios from 62 to 177, the 410W3 winch drive planetary gearbox powers the cranes that lift the heaviest indivisible loads afloat and underground: floating sheerleg cranes positioning bridge sections, offshore construction vessel cranes deploying subsea manifolds, and deep mining shaft winders lowering cages through 500-metre vertical shafts. The 530 Nm brake through ratio 177 produces 93,810 Nm of drum holding torque \u2014 enough to suspend 40 tonnes on a 500 mm PCD drum with a safety factor exceeding 2.4.<\/div>","protected":false},"featured_media":958,"comment_status":"open","ping_status":"closed","template":"","meta":{"_et_pb_use_builder":"","_et_pb_old_content":"","_et_gb_content_width":""},"product_brand":[],"product_cat":[969],"product_tag":[],"class_list":["post-951","product","type-product","status-publish","has-post-thumbnail","product_cat-winch-drive-planetary-gearbox","first","instock","shipping-taxable","product-type-simple"],"_links":{"self":[{"href":"https:\/\/planetary-gearboxes.com\/bs\/wp-json\/wp\/v2\/product\/951","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/planetary-gearboxes.com\/bs\/wp-json\/wp\/v2\/product"}],"about":[{"href":"https:\/\/planetary-gearboxes.com\/bs\/wp-json\/wp\/v2\/types\/product"}],"replies":[{"embeddable":true,"href":"https:\/\/planetary-gearboxes.com\/bs\/wp-json\/wp\/v2\/comments?post=951"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/planetary-gearboxes.com\/bs\/wp-json\/wp\/v2\/media\/958"}],"wp:attachment":[{"href":"https:\/\/planetary-gearboxes.com\/bs\/wp-json\/wp\/v2\/media?parent=951"}],"wp:term":[{"taxonomy":"product_brand","embeddable":true,"href":"https:\/\/planetary-gearboxes.com\/bs\/wp-json\/wp\/v2\/product_brand?post=951"},{"taxonomy":"product_cat","embeddable":true,"href":"https:\/\/planetary-gearboxes.com\/bs\/wp-json\/wp\/v2\/product_cat?post=951"},{"taxonomy":"product_tag","embeddable":true,"href":"https:\/\/planetary-gearboxes.com\/bs\/wp-json\/wp\/v2\/product_tag?post=951"}],"curies":[{"name":"radni list","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}